P1
P2 Fault
IPS-1080-24V
3
4
10/100TX
1
2
7
8
5
6
Quick Installation Guide
Version 1.5
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Safety & Warnings
Dimension
Panel Layouts
1. PWR indicators
2. Faulty relay indicator
3. Link/Act LED for LAN ports
4. PoE LED for LAN ports
5. PoE LAN ports
Package Contents
Front View
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Installation
Step 1:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Step 2:
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1:
Screw the wall-mount kit onto the rear panel of the switch. A total of six
screws are required, as shown below.
Step 2:
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Step 3:
Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
Q I G
IPS-1080-24V
1907-200-XX
Reduced Air Flow:
Installation of the equipment in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
Mechanical Loading:
Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches,
routers,
or
hubs).
Please
refer
to
the
following
table
for
cable
specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1
Unit =mm (Tolerance ±0.5mm)
Features
Contents
Wall-mount Kit
DIN-rail Kit
IPS-1080-24V
Pictures
Number
X 2
X 1
QIG
X 1
X 1
6-pin terminal block
X 1
6
8
.1
5
8
.0
14.0
13.5
40.0
5
0
.0
2
5
.3
41
1
4
4
.3
41
2
4
.7
94.9
2
9
.0
13.1
Ø
3
.0
Ø
5.
9
Ø
4.
0
P1
P2 Fault
IPS-1080-24V
3
4
10/100TX
1
2
7
8
5
6
2
3
4
5
Rear View
1
1. Din-rail screw holes
PWR-1
PWR-2
V2- V2+ V1- V1+
1A@24V
Check Polarity First.
！
Warning
!!!
Top Panel
1. Wall-mount screw holes
2. Terminal blocks: PWR1, PWR2
, Relay
3. DIP Switch
4. Ground wire.
2
3
4
1
1
IPS-1080-24V
Industrial Unmanaged PoE Switch
SWITCH
I N D U S T R I A L
PoE
IPS-1080-24V
IPS-1080-
is unmanaged PoE Ethernet switch with P.S.E. function.
24V
supports Power over Ethernet, a system to transmit electrical power, along with
data, to remote devices over standard twisted-pair cable in an network.
IPS-1080-24V
switch h s 8X10/100Base-T(X) P.S.E. (Power Sourcing Equipment) ports.
P.S.E. is a
a
device (switch or hub for instance that will provide power in a PoE setup.
The
wide operating temperature range from -40 C to 75 C can satisfy most of operating
o
o
environment.
Therefore, the switch is one of the most reliable choices for PoE Ethernet
application.
Provide 8x10/100Base-T(X) PoE (P.S.E.) ports
Supports IEEE 802.3at compliant PoE and total power budget is 120Watts with
maximum 30Watts per port
Advanced PoE power boost technology to support dual 24VDC power inputs
Support auto-negotiation and auto-MDI/MDI-X
Support store and forward transmission
Support flow control
Warning system by relay output
Slim type rigid IP-30 housing design
DIN-Rail and wall mounting enabled
P1
P2 Fault
IPS-1080-24V
3
4
10/100TX
1
2
7
8
5
6