IGS-9084GP-FB2
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
The
series is a managed industrial Ethernet switch with
eight 10/100/1000Base-T(X) ports and four 100/1000Base-X SFP ports. With
fiber optical bypass design, the switch can ensure continued network
operation when any inline device on the network fails. The switch supports
Ethernet Redundancy protocol, O-Ring (recovery time < 30ms over 250 units
of connection) and MSTP (RSTP/STP compatible) to protect mission-critical
applications from network interruptions or temporary malfunctions with fast
recovery technology. With a wide operating temperature from -40 C to 70 C,
the device can be managed centrally via ORing’s proprietary Open-Vision
management utilty as well as via Web-based interfaces, Telnet, and console
(CLI). The switch is one of the most reliable choices for highly-managed and
fiber Ethernet applications.
IGS-9084GP-FB2
o
o
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Safety & Warnings
Dimension
Panel Layouts
7
1. Power LED
2. PWR1 LED
3. PWR2 LED
4. R.M. status LED
5. Ring status LED
6. Faulty relay indicator
7. SFP port
8. Link/action LED for
Gigabit Ethernet ports
Package Contents
Contents
DIN-rail Kit
CD
IGS-9084GP-FB2
Pictures
Number
X 1
X 1
X 1
Front View
Top Panel
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
GIGABIT
I N D U S T R I A L
SWITCH
Industrial Managed Gigabit Switch
QIG
Console Cable
X 2
X 1
X 1
Wall-mount Kit
33.0
30.0
12.5
105.5
10.9
15.0
70.5
154.0
96.4
87.0
48.0
17.5
94.0
124.0
48.0
58.0
7.50
R2.5
R3.95
80.5
62.0
87.9
10
14
1
2
3
4
5
6
Rear View
1
2
PWR-1
PWR-2
1A@24V
DC 48V
V2- V2+
V1- V1+
Fault
1
1. Wall-mount screw holes
2. Din-rail screw holes
2
1. Terminal blocks: PWR1, PWR2
(12-48V DC), Relay
2. Ground wire.
1
Installation
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks
into the rail firmly.
DIN-rail Installation
Step 1:
Step 2:
Step 3:
Screw the two pieces of wall-mount kits onto both ends of the rear panel of the
switch. A total of six screws are required, as shown below.
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
Q I G
1907-2-29-IGS9084GPFB2-1.0
Circuit Overloading:
Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
11
8
9
Network Connection
A
A
Network
B
TX
RX
B
TX
RX
TX
RX
TX
RX
Monitor
9. Duplex LED for Gigabit
Ethernet ports
10. Gigabit Ethernet ports
11. Link/action LED for SFP port
12. Bypass network port
13. Bypass monitor port
14. Console port
15. Reset button
12
13
IGS-9084GP-FB2
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
A
A
Network
B
TX
RX
B
TX
RX
TX
RX
TX
RX
Monitor
IGS-9084GP-FB2
PWR
PWR1
PWR2
10/100/1000T
G8
G6
G4
G2
G12
G11
G10
G9
100/1000X
G7
G5
G3
G1
A
A
Network
B
TX
RX
B
TX
RX
TX
RX
TX
RX
Monitor
The switch provides standard Ethernet ports. According to the link type, the
switch uses CAT 3, 4, 5, 5e UTP cables to connect to any other network devices
(PCs, servers, switches, routers, or hubs). Please refer to the following table for
cable specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
IGS-9084GP-FB2
IGS-9084GP-FB2
15
