Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
i s
m a n a g e d
G i g a b i t
E t h e r n e t
s w i t c h
w i t h
I G P S - 9 8 2 2 D G P +
8x10/100/1000Base-T(X) P.S.E ports and 2x 100/1G/2.5GBase-X + 2x
1G/10GBase-X SFP ports.
The switch support Ethernet Redundancy
protocol, O-Ring (recovery time < 30ms) and MSTP (RSTP/STP compatible)
can protect your mission-critical applications from network interruptions or
temporary malfunctions with its fast recovery technology. IGPS-
also support Power over Ethernet, a system to transmit electrical power up to
30 watts, along with data, to remote devices over standard twisted-pair cable
i n
a n
E t h e r n e t
n e t w o r k .
E a c h
s w i t c h
h a s
I G P S - 9 8 2 2 D G P +
8x10/100/1000Base-T(X) P.S.E. (Power Sourcing Equipment) ports. P.S.E.
is a device (switch or hub for instance) that will provide power in a PoE
connection. And support wide operating temperature from -20 C to 60 C.
o
o
IGPS-
can also be managed centralized and convenient by Open-
Vision, Except the Web-based interface, Telnet and console (CLI)
configuration. Therefore, the switch is one of the most reliable choice for
highly-managed and Fiber Ethernet application.interfaces,
Telnet
and
console (CLI).
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Safety & Warnings
Dimension
Panel Layouts
1. Power LED
2. PWR1 LED
3. PWR2 LED
4. R.M. status LED
5. Ring status LED
6. Fault LED
7. Console port
8. Reset button
9. Link/action LED for
Gigabit PoE LAN ports
Package Contents
Contents
DIN-rail Kit
CD
IGPS-
Pictures
Number
X 1
X 1
X 1
Front View
Top Panel
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
QIG
Console Cable
X 2
X 1
X 1
Wall-mount Kit
11
7
1
2
3
4
5
6
Rear View
1
2
1
1. Wall-mount screw holes
2. Din-rail screw holes
2
1. Terminal blocks: PWR1, PWR2
(50-57V DC), Relay
2. Ground wire.
1
Installation
Step 1:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Step 2:
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks
into the rail firmly.
DIN-rail Installation
Step 1:
Screw the two pieces of wall-mount kits onto both ends of the rear panel of the
switch. A total of six screws are required, as shown below.
Step 2:
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Step 3:
Insert screws through the round screw holes (the red arrow as below) on the
sides or through the cross-shaped aperture (the green arrow as below) in the middle of
the plate and fasten the screw to the wall with a screwdriver.
Step 4:
If the screw goes through the cross-shaped aperture, slide the switch down
before tightening the screw.
Wall-mounting
Q I G
1907-2-29-IGPS-1.0
Mechanical Loading:
Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
10. Gigabit PoE LAN port
11. PoE LED for Gigabit PoE LAN ports
12. 100/1G/2.5GBase-X SFP ports
13. Link/Act LED for SFP port
(100Mbps/1Gbps/2.5Gbps)
14. 1G/10GBase-X SFP ports
15. Link/Act LED for SFP port
(1Gbps/10Gbps)
IGPS-
GIGABIT
I N D U S T R I A L
SWITCH
PoE
Industrial Managed PoE Gigabit Switch
8
10
12
13
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch
uses CAT 3, 4, 5, 5e UTP cables to connect to any other network devices (PCs,
servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
Reset
PWR
PWR1
PWR2
R.M
Ring
Fault
Console
IGPS-
LNK/ACT
PoE
G3
G1
10/100/1000T
G7
G5
G4
G2
G8
G6
G9
100/1G/2.5G
L
N
K
/A
C
T
G12
G11
1G/10G
G10
L
N
K
/A
C
T
Unit =mm (Tolerance ±0.5mm)
Reset
PWR
PWR1
PWR2
R.M
Ring
Fault
Console
IGPS-
LNK/ACT
PoE
G3
G1
10/100/1000T
G7
G5
G4
G2
G8
G6
G9
100/1G/2.5G
L
N
K
/A
C
T
G12
G11
1G/10G
G10
L
N
K
/A
C
T
9
14
15
Reset
PWR
PWR1
PWR2
R.M
Ring
Fault
Console
IGPS-
LNK/ACT
PoE
G3
G1
10/100/1000T
G7
G5
G4
G2
G8
G6
G9
100/1G/2.5G
L
N
K
/A
C
T
G12
G11
1G/10G
G10
L
N
K
/A
C
T
IGPS-