manualshive.com logo in svg

ORiNG IES-3062 Series, User Manual, Page: 48 / 107

Share
Download
ORiNG IES-3062 Series User Manual Download Page 48

IES-3080 / IES-3062 SERIES   User’s Manual 

 

ORing Industrial Networking Corp 

38 

configuration of VLAN operation mode is at “

802.1Q

”. 

 

5.1.4.1  VLAN Setting - IEEE 802.1Q   

Tagged-based VLAN is an IEEE 802.1Q specification standard, and t is possible to create a 

VLAN across devices from different switch venders.    IEEE 802.1Q VLAN uses a technique to 

insert a “tag” into the Ethernet frames.    Tag contains a VLAN Identifier (VID) that indicates the 

VLAN numbers. 

You  can create Tag-based VLAN, and enable or disable GVRP protocol.    There are 256 

VLAN groups to provide configure.    Enable 802.1Q VLAN, the all ports on the switch belong 

to default VLAN, VID is 1.    The default VLAN cannot be deleted. 

GVRP allows automatic VLAN configuration between the switch and nodes.    If the switch is 

connected to a device with GVRP enabled, you can send a GVRP request by using the VID of 

a VLAN defined on the switch; the switch will automatically add that device to the existing 

VLAN. 

 

 

VLAN Configuration – 802.1Q interface 

 

The following table describes the labels in this screen. 

Label 

Description 

VLAN Operation Mode 

Configure VLAN Operation Mode: disable, Port Base,802.1Q 

GVRP Mode 

Enable/Disable GVRP function. 

Management VLAN ID 

Management VLAN can provide network administrator a 

secure VLAN to management Switch.    Only the devices in the 

management VLAN can access the switch. 

Summary of Contents for IES-3062 Series












































































































Reviews:

No comments