manualshive.com logo in svg

ORiNG IES-3062 Series, User Manual, Page: 102 / 107

Share
Download
ORiNG IES-3062 Series User Manual Download Page 102

IES-3080 / IES-3062 SERIES   User’s Manual 

 

ORing Industrial Networking Corp 

92 

6.13  Commands Set List—TFTP command set   

IES-3080 / IES-3062 

SERIES Commands 

Level 

Description 

Defaults 

Example 

backup 

flash:backup_cfg 

G 

Save configuration to 

TFTP and need to 

specify the IP of TFTP 

server and the file 

name of image. 

switch(config)#backup 

flash:backup_cfg 

restore flash:restore_cfg 

G 

Get configuration from 

TFTP server and need 

to specify the IP of 

TFTP server and the 

file name of image. 

switch(config)#restore 

flash:restore_cfg 

upgrade 

flash:upgrade_fw 

G 

Upgrade firmware by 

TFTP and need to 

specify the IP of TFTP 

server and the file 

name of image. 

switch(config)#upgrade  

lash:upgrade_fw 

 

 

6.14  Commands Set List—SYSLOG, SMTP, EVENT command 

set   

IES-3080 / IES-3062 

SERIES Commands 

Level Description 

Example 

systemlog ip   

[IP address]

 

G

  Set System log server 

IP address. 

switch(config)# systemlog ip 

192.168.1.100 

systemlog mode 

[client|server|both] 

G 

Specified the log 

mode 

switch(config)# systemlog mode 

both 

show systemlog

 

E 

Display system log. 

Switch>show systemlog 

show systemlog

 

P

 

Show system log 

client & server 

information 

switch#show systemlog 

 

no systemlog 

G 

Disable systemlog 

functon 

switch(config)#no systemlog 

smtp enable 

G 

Enable SMTP function switch(config)#smtp enable 

smtp serverip 

[IP address] 

G 

Configure SMTP 

server IP 

switch(config)#smtp serverip 

192.168.1.5 

Summary of Contents for IES-3062 Series












































































































Reviews:

No comments