1
2
3
4
5
IES-2050A
P1
P2
Fault
Ring R.M.
P.F.
R.E.
R.M.
R.S.
P5
P2
10/100M
R
in
g
Quick Installation Guide
Version 2.2
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
is a lite-managed Ethernet switch. With very compact size of
IES-2050A
housing, you can install
easily. In addition, it also supports of
IES-2050A
Ethernet Redundancy protocol, O-Ring (recovery time < 10ms over 250 units
of connection), O-Chain and STP/RSTP (IEEE802.1w/D) can protect your
mission-critical applications from network interruptions or temporary
malfunctions with its fast recovery technology.
provides the
IES-2050A
setting ability of Web-GUI and Windows Utility, also support the simple DIP-
Switch setting function which offer great flexibility to set up the Ring.
IES-
2050A
is with rigid IP-30 housing design and can operate under harsh
environment. The feature of wide operating temperature ranges from -40 C
o
to 75 C can satisfy most requirement of operation.
o
•
O-Ring
: O-Ring is ORing's proprietary redundant ring technology, with
recovery time of less 10 milliseconds and up to 250 nodes. The O-Ring
redundant ring technology can protect mission-critical application from
network interruptions or temporary malfunction with its fast recover
technology.
•
O-Chain
: O-Chain is the revolutionary network redundancy technology that
provides the add-on network redundancy topology for any backbone
network, O-Chain allows multiple redundant network rings of different
redundancy protocols to join and function together as a larger and more
robust compound network topology. O-Chain providing ease-of-use while
maximizing fault-recovery swiftness, flexibility, compatibility, and cost-
effectiveness in one set of network redundancy topology.
Package Contents
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Safety & Warnings
Panel Layouts
Front View
1. Power 1 LED
2. R.M status LED
3. Power 2 LED
4. Fault indicator
5. Ring status LED
6. DIP switch
7. LNK/ACT LED for LAN ports
8. LAN port
9. Duplex/Collision LED for LAN ports
IES-2050A
IES-2050A
1907-200-E2050AXXX2-FX022
Contents
DIN-rail Kit
CD
IES-2050A
Pictures
Number
X 1
X 1
X 1
QIG
X 2
X 1
Wall-mount Kit
1
Rear View
1. Din-rail screw holes
Step 1:
Screw the wall-mount kit (in the package) onto the back of the switch. A total
of eight screws are required, as shown below.
Step 2:
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the wall-mounting screws.
Step 3:
Insert a screw head through the large part of the keyhole-shaped aperture on
the plate, and then slide the switch downwards. Tighten the screw for added
stability.
Wall-mounting
Instead of screwing the screws in all the way, it is advised to leave a space of
about 2mm to allow room for sliding the switch between the wall and the
screws.
Network Connection
The series have standard Ethernet ports. Depending on the link type, the switch uses CAT
3, 4, 5, 5e UTP cables to connect to network devices (PCs, servers, switches, routers, or
hubs). Please refer to the following table for cable specifications.
SWITCH
I N D U S T R I A L
Industrial Lite-Managed Switch
2
3
4
5
Step 1:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Step 2:
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks
into the rail firmly.
DIN-rail Installation
1
6
8
7
Top View
2
3
1
1
1. Wall-mount screw holes
2. Terminal block
3. Reset button
4. Ground wire
9
26.1
1
4
4
.3
1
2
3
4
5
IES-2050A
P1
P2
Fault
Ring R.M.
P.F.
R.E.
R.M.
R.S.
P5
P2
10/100M
R
in
g
1
2
3
4
5
IES-2050A
P1
P2
Fault
Ring R.M.
P.F.
R.E.
R.M.
R.S.
P5
P2
10/100M
R
in
g
Mechanical Loading:
Make sure the mounting of the equipment is not in a hazardous
condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of the circuits might have on overcurrent protection
and supply wiring. Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
Dimension
Unit =mm (Tolerance ±0.5mm)
94.9
6
8
.1
5
8
.0
14.0
6.05
25.0
5
0
.0
2
5
.5
8.5
25.6
2
4
.3
Ø5.9
Ø3.0
1
2
.3
13.1
24.3
Ø
4.
0
Installation
Use the mounting kits attached with the package and follow the steps below to install the
switch to a rail or to the wall.
The product is open type, intended to be installed in and industrial control panel or an
enclosure.
PW
R-1
PW
R-2
V2
+ V2
- V1
+ V1
-
1A
@2
4V
DC
12
-4
8V
Re
se
t
PWR-1
PWR-2
V2+ V2- V1+ V1-
1A@24V
DC12-48V
Reset
4
