Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
IES-180-L
1907-2-29-IES180L-1.0
IES-180-L
is an unmanaged Ethernet switch with eight 10/100Base-T(X)
ports in a compact form factor. The easy-to-install switch comes with rigid
IP-30 housing and can operate in harsh environments. The wide operating
temperature range from -20 C to 60 C ensures the switch can operate reliably
in extreme weather conditions.
o
o
Package Contents
Installation
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed cabinet, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mounting of the equipment in the d
should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
in-rail
Safety & Warnings
Contents
Wall-mount Kit
DIN-rail Kit
IES-180-L
Pictures
Number
X 2
X 1
QIG
X 1
Dimension (Unit: mm)
Panel Layouts
Front Panel
1. PWR LED
2. Link/Act indicator for LAN port
3. LAN port
IES-180-L
X 1
1
3
2
Top Panel
1. Terminal block
Real Panel
1
1. Wall-mount screw holes
2. Din-rail screw holes
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
DIN-rail Installation
Step 1:
Step 2:
Step 3:
Screw the two pieces of wall-mount kits onto both sides of the switch. A
total of eight screws are required, as shown below.
Use the switch, with wall mount plates attached, as a guide to mark the correct
locations of
screws.
Insert screw through the large parts of the keyhole-shaped apertures, and then slide
the switch downwards. Tighten the four screws for added stability.
wall-mount
Wall-mounting
SWITCH
I N D U S T R I A L
Industrial Unmanaged Switch
1
IES-180-L
P2
P4
P6
P1
P3
P5
V+
V
-
DC10
~
3
0V
P8
P7
PWR
10/100TX
LNK /ACT
SPEED
100M
10M
IES-180-L
P2
P4
P6
P1
P3
P5
P8
P7
PWR
10/100TX
LNK /ACT
SPEED
100M
10M
25.00
37.00
V+
V-
DC10 ~ 30V
IES-180-L
P2
P4
P6
P1
P3
P5
P8
P7
PWR
10/100TX
LNK /ACT
SPEED
100M
10M
IES-180-L
P2
P4
P6
P1
P3
P5
P8
P7
PWR
10/100TX
LNK /ACT
SPEED
100M
10M
1
2
IES-180-L
P2
P4
P6
P1
P3
P5
P8
P7
PWR
10/100TX
LNK /ACT
SPEED
100M
10M
IES-180-L
P2
P4
P6
P1
P3
P5
P8
P7
PWR
10/100TX
LNK /ACT
SPEED
100M
10M
