Practical Operation
Q I G
Quick Installation Guide
IBS-102FX
IBS-102FX
Version 1.0
Q
uick
I
nstallation
G
uide
ORing Industrial Networking Corp.
Features
IBS-102FX Series
is an external Bypass switch for 100M/1G/10G fiber optical
networks.
This fiber optical bypass switch protects from network failures and
Network maintenance by ensuring network integrity during power loss. This fiber
optical bypass switch includes Network ports and Monitor ports.
The Network ports
are used to connect to main-network connections and provide protection mechanism
and the Monitor ports are used for down-link
networking device. When power
is on, the mode of the Bypass switch is in Normal operation mode and the local
networking device is connected with main-network. When on the power failure state,
the Bypass switch is set to bypass mode to isolate the main-network from the
local networking device .
local
Introduction
Specifications
ORing Bypass Switch Model
Physical Ports
Fiber Ethernet
Optical Fiber
DIP Switch Setting
Power-1 failed warning detection: (On) relay enabled (Off ) relay disabled
DIP-Swicth No.1
LC connector
IBS-102FX-SS-LC
4 Duplex Single-mode LC
connector
Single-mode: 9/125 m
µ
Operating Wavelength
1260 ~ 1570 nm
Environmental
-40 to 85 C (-40 to 185 F)
o
o
Storage Temperature
Operating Temperature
5% to 95% Non-condensing
Operating Humidity
Regulatory approvals
FCC Part 15, CISPR (EN55022) class A
EMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT),
EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27
Shock
IEC60068-2-32
IEC60068-2-6
Vibration
Free Fall
Warranty
1 years
-20 to 70 C (-4 to 158 F)
o
o
DIP-Switch No.2
Fault contact
Relay
Relay output to carry capacity of 1A at 24 VDC
Power
Input power
Power consumption (Typ.)
2.7 Watts
Overload current protection
Present
Physical Characteristic
Enclosure
IP-30
Dimension (W x D x H)
Weight (g)
405g
Dual 12~48 VDC power inputs at DC-Jack and 4-pin terminal block
26.1(W)x94.9(D)x144.3(H) mm (1.03x3.74x5.68inch.)
The Bypass switch deliver the data
between the Network ports and the
Monitor (local) ports
Normal mode:
Industrial Optical Bypass Switch
PRINTED ON RECYCLED PAPER
BYPASS
I N D U S T R I A L
SWITCH
Support 100M/1G/10G optical bypass function of 2 port duplex or 4 port simplex
fiber connection
Different model supported for multi-mode or single-mode optical fiber
Low insertions loss
Throughput not affected and no extra delay
Bypass switching time <10ms
Dual Wide range power inputs: 12~48VDC
Relay output for pwer failed warning
Rigid IP-30 housing design
DIN-Rail and wall mounting enabled
Power Connection Guide
Frame Ground
Power2
Supply
12-48 VDC
V-
V+
Warning
Device
Power1 Input 12-48VDC
Power
Supply
LED Indicators
Green : power LED x 2.
Power indicator
Green On : Operated in normal mode
Normal indicator
1907-2-29-IBS102FX-0
G
PWR2
1A@24V
V+
V- DC12-48V
-
+
Relay
PWR1
The Network data traffic routed directly
to the other Network port. And the Monitor
data traffic routed directly to the other
Monitor port.
Bypass mode:
ORing Industrial Networking Corp.
Copyright© 2011 ORing
All rights reserved.
TEL: +886-2-2918-3036
FAX: +886-2-2918-3084
Website: www.oring-networking.com
E-mail: [email protected]
IBS-102FX-MM-LC
4 Duplex Multi-mode LC
connector
Multi-mode: 50/125µm or 62.5/125µm
Insert loss
typical1.2 dB , Maximun 1.6 dB
Switching time
< 10ms
Power-2 failed warning detection: (On) relay enabled (Off ) relay disabled
Amber for power failed indicator
Fault Indicator
780 ~ 1350 nm
< 1.0 dB
Reverse Polarity
Present on Terminal Block
P1
P2 Fault
IBS -102FX
A
A
100M /1G /10G bps
Network
B
TX
RX
B
TX
RX
TX
RX
TX
RX
Monitor
Alarm
P1
P2
+24V
GND
Nomal mode
Bypass mode
