Features
High Speed Air Connectivity: WLAN interface support up to 54Mbps
Highly Security Capability: WEP/WPA/WPA2/Radius/TKIP supported
Support AP/Bridge/Repeater/AP-Client Mode (for IAP Series)
Ultra fast X-Roaming Technology inside (for IAP Series)
Load balance feature supported (for IAP Series)
Switch Mode Supported: IAP Series supports Daisy Chain to reduce
usage of switch ports
IAR Series supports USB Interface for 3.5G HSDPA USB Modem dial
up
Dual redundant Power Inputs: 12~48VDC on terminal block
Fully Compliant with IEEE802.3af (Power Device at ETH2, PoE
Models)
Event Warning by Syslog, Email, SNMP Trap, Relay output and
Beeper
I
PoE model Support P.D.
AP/IAR series
IAP series
IAP series
IAR series
IAP/IAR series
are reliable IEEE 802.11b/g or IEEE 802.11a/b/g WLAN
with 2 ports LAN Access Point or Access Point Router. It can be
configured to operate in AP/Bridge/Repeater/AP Client mode. You are
able to configure
by Window utility or WEB interface via LAN
port or WLAN interface.
provides dual Ethernet ports in
switch mode, so that you can use Daisy Chain to reduce the usage of
Ethernet switch ports.
provides dual Ethernet port for WAN
port and LAN port. It also provides a USB interface for 3.5G HSDPA
modem dial up. In addition, all PoE models also provide P.D. feature on
ETH2 which is fully compliant with IEEE802.3af PoE specification.
Therefore,
is one of the best communication solution for
wireless application.
PoE model supports P.D. on ETH2 and converts the power from DC
48V for the device. This feature is fully compliant with IEEE802.3af
specification and provides 1KV isolating protection. This P.D. feature
enables PoE Models to speed up the installation of equipment and
extend the range of layout to a maximum of 100 meters without extra
power source.
IAP series contains friendly windows utility, AP-Tool, to explore AP on
local area network. This utility is very helpful for you to search and
configure IP of access point on the industrial network.
Introduction
Windows Utility: AP-Tool
Installation
DIN-Rail Install Step
Wall-mounted Install Step
Applications
Q I G
Version 1.4
Q
uick
I
nstallation
G
uide
ORing Industrial Networking Corp.
Wireless
ACCESS POINT
ACCESS POINT Router
IAP/IAR Series
Quick Installation Guide
IAP/IAR Series
Industrial Wireless LAN Access
Point and Router
Power Connection Guide
Reset
PWR-2
PWR-1
V2+ V2- Relay V1+ V1-
Reset Button
Terminal Block Power-2 Input
Relay Output Pin
Terminal Block Power-1 Input
PRINTED ON RECYCLED PAPER
In practical operation of wireless access point, the wireless access point support
various kinds of operation modes include AP Bridge/Repeater/AP-Client mode.
also support PoE P.D. feature to extend the layout up to
100 meters without extra power source.
You can build up the wireless network
easily.
IAP/IAR series
Various kinds of operation modes
ORing Industrial Networking Corp.
Copyright© 2010 ORing
All rights reserved.
TEL: +886-2-2918-3036
FAX: +886-2-2918-3084
Website: www.oring-networking.com
E-mail: [email protected]
TEL: +886-2-2918-3036
FAX: +886-2-2918-3084
Step 1. Start up the Windows utility
“AP-Tools.exe”
Step 2. Click “Refresh list” button,
the AP device will show on
the list.
Step 3. Configure the IP address
manually.
X-Roaming
1907-2-29-AP-3
Client Mode
