Original Saw Company 3531-01 Operation & Maintenance Manual Download

Page: 1 / 29

This manual is provided for your convenience in the use

and care of your saw. These instructions include opera-

tion, precautions, preventative maintenance and other

pertinent data to assist you in assuring long life and de-

pendable service from your saw.

WARNING:

FOR YOUR SAFETY READ AND

UNDERSTAND THIS MANUAL PRIOR TO

USING THE SAW. REVIEW ALL SAFETY

RULES AND OPERATING INSTRUCTIONS

FREQUENTLY.

RADIAL ARM SAW

TYPE 5

cross cut only

14”

models 3531

01, 3536

01, 3531

03, 3536

16”

models 3541, 3546

For Serial number 20190603790 forward

(July 2019)

Operations & Maintenance Manual

Original Saw Company

465 Third Ave SE

Britt, IA 50423 USA

PH 641

843

3868

800

733

4063

[email protected]

www.originalsaw.com

Getting Started

Unpacking, general machine precautions, wiring,

installation, preventative maintenance.

Summary of Contents for 3531-01






























Search results

Summary of Contents for 3531-01

Reviews:

Related manuals for 3531-01

Brands by name

Popular brands

Original Saw Company 3531-01, Operation & Maintenance Manual

Search results

Summary of Contents for 3531-01

Reviews:

Related manuals for 3531-01

Brands by name

Popular brands