Oracle X7-8 Service Manual Download Page 86

Page: 86 / 308

Troubleshooting Server Subsystems

Cooling Fan Power

Power for the internal PSU cooling fans (zone 0) is provided by the PSUs. Power for the fan

modules (zones 1-4) is supplied by CMOD0, CMOD2, CMOD4, and CMOD6.

■

The chassis cooling fans operate only when the chassis is in main power mode (see

“Power

Control, Shutdown, and Reset States” on page 118

■

The PSU fans operate when the system is in Main power or standby power mode.

The following table lists the CMODs and the fan modules to which they supply power.

CMOD

Fan Modules Powered

CMOD0

FM0 and FM1

CMOD2

FM2 and FM3

CMOD4

FM4 and FM5

CMOD6

FM6 and FM7

Note -

The fan power connectors for CMODs in slots 1, 3, 5, and 7 are not used.

Fan Module Redundancy

The eight fan modules (FMs) provide airflow for chassis cooling zones 1-4. For redundancy,

each zone has two dedicated FMs. Replace a failed fan module immediately. The FMs are hot-

serviceable.

Caution -

Data Loss. Do not remove more than one fan module from a column while the system

is in Main power mode. This action removes power from the CMODs and causes an immediate

shutdown. On an eight-CMOD system, this applies to all fan modules. On a four-CMOD

system, this applies to the fan modules in the left-hand fan frame.

For FM reference and servicing information, see

“Servicing Fan Modules (CRU) and Fan

Frames (CRU)” on page 129

Storage Subsystem

Use the Oracle Integrated Lights Out Manager (ILOM) Storage page to view tables listing

health and inventory information for storage devices detected on your server.

Oracle Server X7-8 Service Manual • October 2017

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands