Oracle X7-8 Service Manual Download Page 77

Page: 77 / 308

Troubleshooting Using Status Indicators

Call

Out

Button

Icon

Description

SP Reset button (recessed) SMOD0

Performs an immediate System A (SMOD0) SP reboot and requires a stylus.

Host Warm Reset button (recessed)

SMOD0

Performs an immediate System A (SMOD0) host reboot and requires a stylus.

Non-maskable Interrupt (NMI)

button (recessed) SMOD1

Do not press. This button is used by Oracle Service personnel only and

requires a stylus.

SP Reset button (recessed) SMOD1

Performs an immediate System B (SMOD1) SP reboot and requires a stylus.

Host Warm Reset button (recessed)

SMOD1

Performs an immediate System B (SMOD1) host reboot and requires a stylus.

Status Indicator Blink Rates

This section describes the following indicator blink rates:

■

Steady On

■

Steady Off

■

Slow Blink Rate

■

Fast Blink Rate

■

Single (Standby) Blink Rate

■

Slow Unison Blink Rate

■

Insertion Blink

■

Unison Steady On

■

Alternating (Invalid FRU) Blink Rate

■

Feedback Flash

■

Data Blink Rate

■

Sequential (Diagnostic) Blink Rate

Steady On

For the steady on state, an indicator is continually on (lit) and does not blink. This indicates a

continuing condition, for example, an operational state (green) or a Service Action Required

fault state (amber).

Troubleshooting and Diagnostics

Summary of Contents for X7-8





















































































































































































































































































































Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands

Oracle X7-8, Service Manual

Search results

Summary of Contents for X7-8

Reviews:

Brands by name

Popular brands