Oracle X7-2 Installation Manual Download

Page: 78 / 148

Preparing for Installation and Power On

Properties:

active_media = SFP28

auto_media_detection = enabled

current_active_media = SFP28

Commands:

set

show

-> show current_active_media

/HOST/network

Properties:

current_active_media = SFP28

-> set active_media=RJ45

Set 'active_media' to 'RJ45'

Reset or power the host for the new host media to take effect.

Preparing for Installation and Power On

Setting up the server for the first time takes about 1 hour. If you are installing optional

components and rackmounting hardware, plan for additional time.

Caution -

Do not apply main power until instructed to do so.

The server uses a service

processor (SP) to configure and boot the host server. To configure the host server and to

view SP messages, do not apply AC power to the server until the SP and host networking

connections are made.

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands