Oracle X7-2 Installation Manual Download Page 117

Page: 117 / 148

Installing an Operating System

14.

Scroll to the bottom of the Create RAID Volume screen and select

Create Volume

Press

Enter

15.

The volume appears under RAID volumes. Press

ESC

to return to the Main BIOS

Setup Utility menu.

16.

On the Save and Exit screen, select

Save Changes and Exit

and press

Enter

This completes the RAID configuration. You can now install an operating system on the volume

that you created.

Installing an Operating System

For details on installing an operating system on Oracle Server X7-2 and Oracle Server X7-2L,

refer to

Oracle Servers X7-2 and X7-2L Operating Systems Installation Guide

Configuring Storage Drives for Operating System Installation

117

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands