manualshive.com logo in svg

Oracle X6 series, Administration Manual, Page: 18 / 126

Share
Download
Oracle X6 series Administration Manual Download Page 18

Oracle Hardware Management Pack

18

Oracle X6 Series Servers Administration Guide • April 2016

Once you have installed Oracle Hardware Management Pack, you can enter Oracle Hardware

Management Pack commands from the operating system command-line application. This

guide details some of the tasks you can perform using the Oracle Server CLI Tools included

in Oracle Hardware Management Pack. For information about other components mentioned in
this section, refer to the Oracle Hardware Management Pack Documentation Library at 

http:

//www.oracle.com/goto/ohmp/docs

. To download and install Oracle Hardware Management

Pack, see 

“Accessing Oracle Hardware Management Pack” on page 31

.

For more information about the software, see the following sections:

■

“Oracle Hardware Management Pack Utilities” on page 18

■

“Oracle Hardware Management Pack Documentation” on page 19

Oracle Hardware Management Pack Utilities

The following table lists and describes the Oracle Hardware Management Pack utilities. The

utilities work with most supported operating systems. Additionally, utility commands can be

scripted to support multiple servers, as long as the servers are of the same type.

Note - 

Oracle Hardware Management Pack includes components that are not included in this

guide. Refer to the Oracle Hardware Management Pack documentation for more comprehensive

information.

CLI Tool

Description

ubiosconfig

Preserve BIOS settings and some service processor settings.

fwupdate

Update Oracle ILOM and BIOS; or query, update, and validate firmware versions

on supported SAS storage devices, embedded SAS storage controllers, SAS

storage expanders, storage drives, InfiniBand controllers, and Fibre Channel

controllers.

raidconfig

View or create RAID volumes on storage drives that are attached to RAID

controllers.

ilomconfig

Restore, set, and view Oracle ILOM settings, such as network management,

clock configuration, and user management settings.

hwtmgmtcli

Monitor system health.

ipmitool

After loading the requisite driver, use Oracle Hardware Management Pack to read

sensor data repository (SDR) data and display other information about the server.

You can also get and set LAN configuration parameters and perform chassis

power control operations.

snmpwalk

Read information about the server indicator and sensor readings from the system

event log; or set the location indicator.

itpconfig

Configure Oracle ILOM to forward SNMP traps to the host.

Summary of Contents for X6 series































































































































Reviews:

No comments