manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 341

POST and Checkpoint Codes

This section describes the server boot POST and checkpoint codes.

As the system powers on, it displays power-on self test (POST) codes that provide information

about the state of the system. The codes are primarily generated by the system BIOS

(exceptions are noted).

AMI Checkpoint Ranges

Status Code

Range

Description

0x01 - 0x0B

SEC execution (PEI).

0x0C - 0x0F

SEC errors.

0x10 - 0x2F

PEI execution up to and including memory detection.

0x30 - 0x4F

PEI execution after memory detection.

0x50 - 0x5F

PEI errors.

0x60 - 0x8F

DXE execution up to BDS.

0x90 - 0xCF

BDS execution.

0xD0 - 0xDF

DXE errors.

0xE0 - 0xE8

S3 fesume (PEI).

0xE9 - 0xEF

S3 resume errors (PEI).

0xF0 - 0xF8

Recovery (PEI).

0xF9 - 0xFF

Recovery errors (PEI).

POST and Checkpoint Codes

341

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands