manualshive.com logo in svg

Oracle X5-4, Service Manual

The Oracle X5-4 is a powerful and versatile server, designed for high-performance computing. To get acquainted with its features and functionalities, make sure to download the free "Getting Started Manual" from our website. This comprehensive manual will provide you with all the necessary information to maximize your experience with the Oracle X5-4.

Share
Download
background image

Install an NVMe Storage Drive in the Server

pcie101              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@5
pcie102              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@6
pcie103              ENABLED         PCIe-Native
/pci@0,0/pci8086,2f06@2,2/pci111d,80b5@0/pci111d,80b5@7

Install an NVMe Storage Drive in the Server

Perform this procedure to physically install an NVMe storage drive into the server.

Note - 

After you physically remove an NVMe storage drive from the server, wait at least 10

seconds before installing a replacement drive.

1.

Remove the replacement drive from its packaging and place the drive on an

antistatic mat.

2.

If necessary, remove the drive filler panel.

3.

Align the replacement drive with the drive slot.

The drive is physically addressed according to the slot in which it is installed. It is important to

install a replacement drive in the same slot as the drive that was removed.

4.

Slide the drive into the slot until the drive is fully seated.

See 

“Install a Storage Drive (CRU)” on page 118

.

5.

Close the drive latch to lock the drive in place.

Power On an NVMe Storage Drive

Before You Begin

■

To perform this task, the hotplug daemon must be enabled on the host.

■

For a list of the virtual PCIe slots of NVMe drives as seen by the operating system, see

“NVMe Storage Drive Virtual PCIe Slot Designation” on page 115

. Note that the virtual

PCIe slot name is not the same as the name on the server front panel label.

1.

Power on the slot for the drive. Type:

# 

hotplug enable pcie100

In this example, 

pcie100

 is the drive labeled NVMe0 on the server front panel.

124

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Related manuals for X5-4

IBM eServer 200 xSeries User Reference Manual preview
eServer 200 xSeries
Brand: IBM Pages: 128
IBM eServer 232 xSeries User Reference Manual preview
eServer 232 xSeries
Brand: IBM Pages: 174
IBM QS21 - BladeCenter - 0792 Installation And User Manual preview
QS21 - BladeCenter - 0792
Brand: IBM Pages: 110
IBM eserver xSeries 306 Option Installation Manual preview
eserver xSeries 306
Brand: IBM Pages: 46
IBM 84885BU Maintenance And Troubleshooting Manual preview
84885BU
Brand: IBM Pages: 200
Digital Equipment DIGITAL Server 9100 Series User Manual preview
DIGITAL Server 9100 Series
Brand: Digital Equipment Pages: 68
TYANO GX38-B5550 Service Engineer'S Manual preview
GX38-B5550
Brand: TYANO Pages: 68
IBM 88743BU - System x3950 E User Manual preview
88743BU - System x3950 E
Brand: IBM Pages: 426
IBM 7944E2U User Manual preview
7944E2U
Brand: IBM Pages: 21
Supermicro SuperServer 6029U-TR25M User Manual preview
SuperServer 6029U-TR25M
Brand: Supermicro Pages: 151
FS 139690 Quick Start Manual preview
139690
Brand: FS Pages: 91
Allnet FW8888 Quick Installation Manual preview
FW8888
Brand: Allnet Pages: 12
BayTech LASERSHARE PS-MIO Owner'S Manual preview
LASERSHARE PS-MIO
Brand: BayTech Pages: 133
Silicon Graphics UV 30 User Manual preview
UV 30
Brand: Silicon Graphics Pages: 66
Supero 1017A-MP User Manual preview
1017A-MP
Brand: Supero Pages: 91
Supero 1026T-6RF+ User Manual preview
1026T-6RF+
Brand: Supero Pages: 108
Supero 1042G-TF User Manual preview
1042G-TF
Brand: Supero Pages: 118
Supero SC835XTQ - R982B User Manual preview
SC835XTQ - R982B
Brand: Supero Pages: 80

Brands by name

Popular brands

Load more brands