manualshive.com logo in svg

Oracle X5-4, Service Manual

Share
Download
Oracle X5-4 Service Manual Download Page 106

Remove Power

Remove Power

To completely remove power from the server, disconnect the AC power cables from the back of

the server.

This might be necessary to perform a cold reset, or to place it in a non-powered state for cold

servicing.

1.

Place the server in standby power mode.

Use one of the power off methods. See 

“Powering Off the server” on page 101

.

2.

If necessary, do the following:

a.   

Extend the server to the maintenance position.

b.   

Position the CMA.

3.

Access the back of the server.

4.

Remove the power cord retainer clips by lifting them up to disengage them from

the power cords.

106

Oracle Server X5-4 Service Manual • December 2015

Summary of Contents for X5-4







































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands