Oracle Sun Server X4-4 Page 66 Installation Manual Download

Page: 66 / 148

Exit Oracle ILOM

The Network Configuration Test screen appears.

Select Ping or Ping6 from the Test Type list box.

Choose a Ping test for an IPv4 network configuration. Choose a Ping6 test for an IPv6 network

configuration.

Type the IPv4 or IPv6 test destination address in the Destination field and click

Test.

If the test was successful, a “Ping of

ip_address

succeeded” message appears below the

Destination field in the Network Configuration Test screen.

Exit Oracle ILOM

To end an Oracle ILOM session:

■

From the Oracle ILOM CLI, type

exit

at the CLI prompt.

■

From the Oracle ILOM web interface, click the Log Out button at the top-right

corner of the page.

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands