Oracle Sun Server X4-4 Installation Manual Download Page 32

Page: 32 / 148

Optional Component Installation

Optional Component Installation

Standard system components are installed at the factory. Optional components that you

purchased independent of the standard configuration are shipped separately, and in most cases

should be installed before you install the server in a rack.

The following optional components can be ordered and purchased separately:

■

PCIe cards

■

DDR3 DIMM memory kits

■

Storage drives

■

Software media

If you ordered any customer-installable components, refer to the service label on the top cover

of the server or the component removal and replacement procedures in the

Sun Server X4-4

Service Manual

Supported components and their part numbers are subject to change over time and without

notice. For the most up-to-date list, refer to:

https://support.oracle.com/handbook_private/

Note -

This site requires an Oracle web account for access.

Click the name and model of your server. On the product page that opens for the server, click

Full Components List for a list of supported components.

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Brands by name

Popular brands