Oracle Sun Server X4-4 Installation Manual Download

Page: 30 / 148

Shipping Inventory

These clearance values are based on the inlet and exhaust impedance (available open area)

stated here and assume a uniform distribution of the open area across the inlet and exhaust

areas. These values also improve cooling performance.

Note -

The combination of inlet and exhaust restrictions, such as cabinet doors and the

spacing of the server from the doors, can affect the cooling performance of the server.

You must evaluate these restrictions. Server placement is particularly important for high-

temperature environments.

■

Take care to prevent recirculation of exhaust air within a rack or cabinet.

■

Manage cables to minimize interference with the server exhaust vent.

Shipping Inventory

Inspect the shipping cartons for evidence of physical damage. If a shipping carton appears

damaged, request that the carrier's agent be present when the carton is opened. Keep all contents

and packing material for the agent's inspection.

The following items are typically packaged with the Sun Server X4-4:

Callout

Description

Server

Cable management assembly

Rackmount kit

Antistatic wrist strap

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands