manualshive.com logo in svg

Oracle Sun Server X4-4, Installation Manual

Share
Download
Oracle Sun Server X4-4 Installation Manual Download Page 135

Powering Off the Server for Orderly Shutdown

Note - 

If the boot mode is UEFI, some of these options are only be available in the BIOS Setup

Utility.

3.

Once POST completes, the system attempts to boot from either the default boot

device, or the temporary boot device selected from the BBS Popup menu. If

available, an operating system is loaded.

The system is ready for use.

Powering Off the Server for Orderly Shutdown

Use the procedures in one of the following sections to perform an orderly shutdown. These

procedures cause ACPI-enabled operating systems to perform an orderly shutdown of the

operating system. Servers not running ACPI-enabled operating systems shut down to standby

power mode immediately.

Note - 

To completely power off the server, you must disconnect the power cords from the back

panel of the server.

■

“Use the Power Button for Orderly Shutdown” on page 136

Controlling System Power and Viewing BIOS Messages

135

Summary of Contents for Sun Server X4-4





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands