manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 50

Locate the Server

■

At the Oracle ILOM prompt type:

-> 

show /System

 
/System
   Targets:
. . .

In the output look for a line under Properties that identifies the product serial number. For

example:

serial_number = BKL1026F8F

Related Information

■

“Front Panel Components (Service)” on page 13

Locate the Server

You can use the Locate indicators to identify one particular server from many other servers.

1.

At the Oracle ILOM prompt, type,

-> 

set /System locator_indicator=on

The white System Locate indicators (one on the front panel and one on the rear panel) blink.

2.

After locating the server with the blinking System Locate indicator, turn it off by

pressing the Locate button with a stylus.

Alternatively, you can type an Oracle ILOM command to turn off the System Locate indicator.

-> 

set /System locator_indicator=off

Related Information

■

“Front Panel Components (Service)” on page 13

50

SPARC T8-2 Server Service Manual • June 2019

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands