manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 58 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 58

Remove the Cable Management Arm

5.

For both types of kits, remove the two screws securing each hardmount bracket

at the front of the rack.

6.

For the sliding rail kit, extend the server to the locked position, then press the

release buttons on the rails to pull the server out of the rack.

7.

Lift the server from the rack and set it aside on an antistatic mat.

8.

Remove the top cover.

See 

“Remove the Top Cover” on page 67

.

Related Information

■

“Prevent ESD Damage” on page 55

■

“Remove the Top Cover” on page 67

■

“Install the Top Cover” on page 246

■

“Safety Information” on page 44

Remove the Cable Management Arm

Follow this procedure to remove the optional 19-inch sliding rail kit with the CMA. The CMA

applies only to the 4-Post, 19-Inch rack with sliding rails for servers.

Before you begin this procedure, refer to 

“Installing the 19-Inch Sliding Rail Kit With the

CMA” in 

Netra SPARC S7-2 Server Installation Guide

 and identify CMA connectors A, B, C,

58

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments