manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual

The Oracle Netra SPARC S7-2 comes packed with cutting-edge features for optimal performance. To ensure seamless installation, simply download the user manual for free from manualshive.com, and get step-by-step instructions for easy setup. Find everything you need in the comprehensive installation manual, available for hassle-free download.

Share
Download
background image

Determine if the Motherboard Is Faulty

Determine if the Motherboard Is Faulty

You must determine if the motherboard is faulty before you replace it.

1.

Check to see if any Server Service Required LEDs are lit or flashing.

See 

“Front Panel Components (Service)” on page 17

.

2.

In Oracle ILOM, check the health of the system processors.

-> 

show /System/Processors 

 /System/Processors
  Targets:
  CPUs
  Properties:
   health = OK
   health_details = -
...
->

3.

Check the health of the individual CPUs.

-> 

show /System/Processors/CPUs/CPU_

x

 

 /System/Processor/CPUs/CPU_0
  Targets:
  Properties:
   health = OK
   health_details = -
...
->

where 

x

 is the number of the CPU, either 

0

 or 

1

.

4.

Check the health of the networking system.

-> 

show /System/Networking 

 /System/Networking
  Targets:
   Ethernet_NICs
  Properties:
   health = OK
   health_details = -
...
->

5.

Check the health of the individual interfaces.

226

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments

Related manuals for Netra SPARC S7-2

Panasonic KX-NS1000 Quick Reference Manual preview
KX-NS1000
Brand: Panasonic Pages: 28
IBM Power 720 Express 8202-E4B Installation Manual preview
Power 720 Express 8202-E4B
Brand: IBM Pages: 64
IBM PS700 Technical Overview And Introduction preview
PS700
Brand: IBM Pages: 148
IBM 5104-22C Manual preview
5104-22C
Brand: IBM Pages: 36
IBM AS/400e User Handbook Manual preview
AS/400e
Brand: IBM Pages: 834
Moxa Technologies NPort P5250A Series Quick Installation Manual preview
NPort P5250A Series
Brand: Moxa Technologies Pages: 2
SEH SEH InterCon PS54a-G Hardware Installation Manual preview
SEH InterCon PS54a-G
Brand: SEH Pages: 24
Western Digital Ultrastar Serv60+8 User Manual preview
Ultrastar Serv60+8
Brand: Western Digital Pages: 406
MAXDATA PLATINIUM 9000-4R User Manual preview
PLATINIUM 9000-4R
Brand: MAXDATA Pages: 18
IBM xSeries 206 User Manual preview
xSeries 206
Brand: IBM Pages: 58
IBM System x3500 M4 Installation And User Manual preview
System x3500 M4
Brand: IBM Pages: 170
Viavi Gen2 GigaStor Hardware Installation preview
Gen2 GigaStor
Brand: Viavi Pages: 7
Datum TYMSERVE 2000 Operation And Technical Manual preview
TYMSERVE 2000
Brand: Datum Pages: 54
Planet NAS-7102 User Manual preview
NAS-7102
Brand: Planet Pages: 68
B+B SmartWorx VESP211 Quick Start Manual preview
VESP211
Brand: B+B SmartWorx Pages: 2
AirLive WFP-101U User Manual preview
WFP-101U
Brand: AirLive Pages: 133
Redline RDL-2000 User Manual preview
RDL-2000
Brand: Redline Pages: 50
Supero A+ SERVER 1022G-NTF User Manual preview
A+ SERVER 1022G-NTF
Brand: Supero Pages: 116

Brands by name

Popular brands

Load more brands