Oracle Netra SPARC S7-2 Service Manual Download Page 208

Page: 208 / 258

Remove NVMe Cables

Remove NVMe Cables

Replacing the cable assembly is a cold-service procedure that must be performed by qualified

service personnel. The server must be completely powered down before performing this

procedure.

Prepare for service.

See

“Preparing for Service” on page 43

Disconnect the NVMe cables from the motherboard and front storage drive

backplane.

Tip -

Take a photograph or note the cable routing and order, for use later when installing the

cables.

Press each latch, then pull out to disengage the cable from each connector.

Remove the SAS cables from the backplane.

See

“Remove the SAS Drive Signal Cable” on page 196

and

“Remove HBA SAS

Cables” on page 211

208

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 208 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: