Oracle Netra SPARC S7-2 Service Manual Download Page 204

Page: 204 / 258

Remove the PDB Signal Cable

■

“Component Service Task Reference” on page 47

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Remove the PDB Signal Cable

Removing a cable is a cold-service operation. You must power off the server before you remove

the cable.

Determine which cable to remove.

See

“Cable Configurations” on page 194

Prepare for service.

See

“Preparing for Service” on page 43

Review this information and complete these prerequisites in this order.

See:

■

“Remove a Fan Module” on page 153

Remove all fan modules.

■

“Remove the Fan Tray” on page 69

■

“Rotate the Drive Cage to the Service Position” on page 71

■

“Remove the Air Duct” on page 75

■

“Remove the PSU Duct” on page 74

204

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 204 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: