manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 200 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 200

Remove the Drive Power Cable

Description

Links

Install a cable as part of another component's

service operation.

“Install the Drive Power Cable” on page 202

Related Information

■

“Identifying Components” on page 13

■

“Detecting and Managing Faults” on page 25

■

“Component Service Task Reference” on page 47

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Remove the Drive Power Cable

Removing a cable is a cold-service operation. You must power off the server before you remove

the cable.

1.

Determine which cable to remove.

See 

“Cable Configurations” on page 194

.

2.

Prepare for service.

See 

“Preparing for Service” on page 43

.

3.

If you are removing the drive power cable from the motherboard, complete these

prerequisites in this order.

See:

■

“Remove a Fan Module” on page 153

Remove all fan modules.

■

“Remove the Fan Tray” on page 69

4.

Disconnect the drive power cable from the drive backplane.

See 

“Cable Configurations” on page 194

.

5.

Release the cable from the cable clamp.

6.

If applicable, disconnect the cable from the motherboard.

200

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments