manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual, Page: 20 / 258

Share
Download
Oracle Netra SPARC S7-2 Service Manual Download Page 20

Field-Replaceable Units

Related Information

■

“Detecting and Managing Faults” on page 25

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Field-Replaceable Units

FRUs can only be serviced by Oracle authorized service personnel. Damage to the components

and the server might occur if the FRUs are improperly serviced.

Description

Links

LED board

“Servicing the LED Board” on page 217

Disk drive backplane

“Servicing the Drive Backplane” on page 117

USB board

“Servicing the USB Board” on page 109

PDB

“Servicing the PDB” on page 141

Motherboard

“Servicing the Motherboard” on page 225

Related Information

■

“Detecting and Managing Faults” on page 25

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Device Paths

This table describes the device paths for servers populated with two CPUs.

Device

Path

PCIe 1

/pci@300/pci@1/pci@0/pci@a

PCIe 2

/pci@300/pci@1/pci@0/pci@11

20

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments