manualshive.com logo in svg

Oracle Netra SPARC S7-2, Service Manual

The Oracle Netra SPARC S7-2 comes packed with cutting-edge features for optimal performance. To ensure seamless installation, simply download the user manual for free from manualshive.com, and get step-by-step instructions for easy setup. Find everything you need in the comprehensive installation manual, available for hassle-free download.

Share
Download
background image

Remove the SAS Drive Signal Cable

■

“Detecting and Managing Faults” on page 25

■

“Component Service Task Reference” on page 47

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Remove the SAS Drive Signal Cable

Removing a cable is a cold-service operation. You must power off the server before you remove

the cable.

1.

Determine which cable to remove.

See 

“Cable Configurations” on page 194

.

2.

Prepare for service.

See 

“Preparing for Service” on page 43

.

3.

Remove the fan tray with all fan modules.

See 

“Remove the Fan Tray” on page 69

.

4.

Disconnect the SAS drive signal cable connector from the drive backplane.

See 

“Cable Configurations” on page 194

.

5.

Remove the air duct.

See 

“Remove the Air Duct” on page 75

.

6.

Disconnect the cable connector from the HBA card in slot 7.

Tip - 

Take a photo or note the cable routing and order for use later when installing the cables.

7.

Set the cable aside.

8.

Consider your next step.

■

If you are replacing a cable, install the new cable.

See 

“Install the SAS Drive Signal Cable” on page 197

.

■

If you removed a cable as part of another component's removal or

installation procedure, return to that procedure.

196

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Reviews:

No comments

Related manuals for Netra SPARC S7-2

IBM x3100 M5 Type 5457 Installation And Service Manual preview
x3100 M5 Type 5457
Brand: IBM Pages: 688
H3C UniServer R2700 G3 User Manual preview
UniServer R2700 G3
Brand: H3C Pages: 226
IBM BladeCenter PS703 Technical Overview And Introduction preview
BladeCenter PS703
Brand: IBM Pages: 198
Compaq AlphaServer ES45 1B Owner'S Manual preview
AlphaServer ES45 1B
Brand: Compaq Pages: 322
Seyeon FW3150 User Manual preview
FW3150
Brand: Seyeon Pages: 10
Nokia Alcatel-Lucent OXO Connect Compact Installation Manual preview
Alcatel-Lucent OXO Connect Compact
Brand: Nokia Pages: 216
Nortel CallPilot 1005r Hardware Installation preview
CallPilot 1005r
Brand: Nortel Pages: 74
Nortel Communication Server 100 Manual preview
Communication Server 100
Brand: Nortel Pages: 214
Planet Networking & Communication ICS-2200T User Manual preview
ICS-2200T
Brand: Planet Networking & Communication Pages: 67
Planet Networking & Communication ICS-2100T User Manual preview
ICS-2100T
Brand: Planet Networking & Communication Pages: 76
Z Microsystems ZX2 User Manual preview
ZX2
Brand: Z Microsystems Pages: 21
ICP DAS USA tDS-700 Series Quick Start Manual preview
tDS-700 Series
Brand: ICP DAS USA Pages: 8
Uniwide UniServer 1522LV User Manual preview
UniServer 1522LV
Brand: Uniwide Pages: 68
GIGA-BYTE TECHNOLOGY R181-T90 User Manual preview
R181-T90
Brand: GIGA-BYTE TECHNOLOGY Pages: 68
PrimeArray 4xxx User Manual preview
4xxx
Brand: PrimeArray Pages: 208
Gateway GR160 F1 Specifications preview
GR160 F1
Brand: Gateway Pages: 14
Inspur NF5488A5 User Manual preview
NF5488A5
Brand: Inspur Pages: 51
Quest Engineering DR4300e Owner'S Manual preview
DR4300e
Brand: Quest Engineering Pages: 181

Brands by name

Popular brands

Load more brands