Oracle Netra SPARC S7-2 Service Manual Download Page 156

Page: 156 / 258

Install a Fan Module

Press the fan module down until it clicks securely into the fan tray.

Repeat from

Step 2

through

Step 4

for any additional fan modules that you are

installing.

If you installed a fan module as part of another component's removal or

installation procedure, return to that procedure.

See

“Component Service Task Reference” on page 47

for assistance.

Complete these postrequisites in this order to finish the installation procedure.

See:

■

“Returning a Server to Operation” on page 235

■

“Verify a Fan Module” on page 157

Related Information

■

“Remove a Fan Module” on page 153

■

“Verify a Fan Module” on page 157

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

156

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Oracle Netra SPARC S7-2, Service Manual, Page: 156 / 258

Search results

Summary of Contents for Netra SPARC S7-2

Reviews: