Oracle Netra SPARC S7-2 Installation Manual Download Page 40

Page: 40 / 102

Installing the 19-Inch Sliding Rail Kit With the CMA

11.

Connect required and optional cables.

See

“Connecting Cables” on page 61

12.

Consider your next step:

■

For an existing server, return the server to operation by following the steps

in the service manual.

■

For a new server, continue the installation by following the steps in this

guide.

Related Information

■

“19-Inch Hardmount Kit (4-Post Rack) Components” on page 35

■

“Tools Needed for Installation” on page 29

■

“Handling Precautions” on page 28

■

“Rack Cautions” on page 32

Installing the 19-Inch Sliding Rail Kit With the CMA

These topics describe how to install the server using the optional 19-inch sliding rail kit with the

CMA.

■

“19-Inch Sliding Rail Kit With the CMA Components” on page 41

■

“Install the Server (4-Post, 19-Inch Sliding Rails With CMA Rack Kit)” on page 42

Related Information

■

“Tools Needed for Installation” on page 29

■

“Handling Precautions” on page 28

■

“Rack Cautions” on page 32

Netra SPARC S7-2 Server Installation Guide • January 2017

Summary of Contents for Netra SPARC S7-2







































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Installation Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands