manualshive.com logo in svg

Oracle Acme Packet 6300, Hardware Installation And Maintenance Manual, Page: 85 / 131

Share
Download
Oracle Acme Packet 6300 Hardware Installation And Maintenance Manual Download Page 85

Installing the Power Supply

4.

Push the power supply handle until the power supply is engaged with the chassis.

5.

The power supply is installed in the Acme Packet 6300/6350 chassis.

Note:

Connect the power cord to the inserted power supply.

NIU/TCU Removal and Installation

This section describes how to remove and replace either an NIU or a transcoding
Carrier Unit (TCU). Both of these components are fastened to the rear of the Acme
Packet 6300/6350 using the same type hardware (i.e., ejection levers and captive
thumbscrews).

Prior to removing an NIU/TCU, the platform in which it is installed must be in standby
before powering down the chassis and removing the component(s). The following
procedure describes how to remove an NIU/TCU.

Note:

Make sure you are properly grounded with an ESD strap before removing the
NIU/TCU.

Note:

Images in this section reflect the Acme Packet 4600. The procedures are the
same for the AP6350 NIU and TCU.

Chapter 6

NIU/TCU Removal and Installation

6-13

Summary of Contents for Acme Packet 6300




































































































































Reviews:

No comments