manualshive.com logo in svg

Oracle Acme Packet 3900, Hardware Installation And Maintenance Manual, Page: 16 / 70

Share
Download
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual Download Page 16

Ethernet cable can be used between the Acme Packet 3900 and the console

adapter.

Network Management Ports

The Acme Packet 3900 has three network management ports located on the rear left
side of the chassis, labeled Mgmt 0, Mgmt 1, and Mgmt 2. These 10/100/1000 Base-
T Ethernet ports are used for EMS control, RADIUS accounting, CLI management,
SNMP queries and traps, and other management functions.

Ethernet LED

Each network management Ethernet port has two integrated LEDs: one LED indicates
Link, and the other indicates Activity. The LED pair is located directly above its
associated port.

Link LED

The link LED is located to the top left side of the network management Ethernet port.
This LED illuminates yellow when a link has been established between the link partner
device and the Acme Packet 3900.

Activity LED

The activity LED is located at the top right side of the network management Ethernet
port. The activity LED illuminates green when an Ethernet connection has either
transmit or receive packet activity.

Upon initial bootup of the Acme Packet 3900, the network management Ethernet ports
are not configured. You must first connect to the Acme Packet 3900 over a serial
connection before you can configure the management Ethernet ports for use. Set
up the management interfaces using the physical and network interface configuration
elements. Refer to the System Configuration chapter of the Configuration Guide for
details.

Chapter 2

Control Panels

2-5

Summary of Contents for Acme Packet 3900







































































Reviews:

No comments