manualshive.com logo in svg

Oracle Acme Packet 3900, Hardware Installation And Maintenance Manual, Page: 14 / 70

Share
Download
Oracle Acme Packet 3900 Hardware Installation And Maintenance Manual Download Page 14

High Availability Mode LEDs

If you configure the Acme Packet 3900 as part of a High Availability pair, these LEDs
will specify the current HA mode for the unit; whether the unit is in Standby or Active
Mode. If the unit is not part of an HA pair these LEDs will not be lit.

Alarm LED

The Alarm LED will be lit when the unit is in alarm mode. See Appendix A of this
document for a list and description of the alarm conditions that will activate this LED.

Power LED

The green PWR LED indicates the operational state of the chassis.

•

on — indicates that power is being applied to the chassis.

•

off — indicates that power is not being applied to the chassis.

Power Pushbutton

Pressing the front panel Power Pushbutton will turn on or off the Acme Packet 3900.
After the power is turned on, the Acme Packet 3900 begins its boot sequence and
loads the configured software file.

Do not turn off the unit using the Power Pushbutton until you have performed a
graceful shutdown of the unit. Pressing the power button without gracefully shutting
down the unit can result in loss of data.

Rear Panel

The Acme Packet 3900 comes with the Rear Panel as a permanent part of the
chassis. All the Signaling, Media and Network Management ports are located on the
Rear Panel of the chassis.

Chapter 2

Control Panels

2-3

Summary of Contents for Acme Packet 3900







































































Reviews:

No comments