Oracle 1242 User Manual Download Page 62

Page: 62 / 84

Servicing Doors

The grounding terminal is located under the cabinet between the two rear casters on the inside

of the caster plate.

Attach the other end of the grounding cable to a reliable earth ground in the

building using established electrical guidelines and in accordance with electrical

codes for the country of installation.

Caution -

If the installed equipment makes additional connections to earth ground, ensure that

all grounding points reference the same earth ground to prevent dangerous ground loops.

Servicing Doors

This section provides instructions for removing and replacing the doors on the rack. You might

need to remove the doors in order to install or cable certain equipment in the rack.

■

“Remove the Doors” on page 63

■

“Install the Doors” on page 65

Oracle Rack Cabinet 1242 User's Guide • July 2018

Summary of Contents for 1242





















































































Search results

Summary of Contents for 1242

Reviews:

Related manuals for 1242

Brands by name

Popular brands

Oracle 1242, User Manual

Search results

Summary of Contents for 1242

Reviews:

Related manuals for 1242

Brands by name

Popular brands