OPTO 22
• 800-321-6786 • 1-951-695-3000 • www.opto22.com • [email protected]
© 2019-2020 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
OPTO 22
• 800-321-6786 • 1-951-695-3000 • www.opto22.com • [email protected]
© 2019-2020 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
PAGE 3
Form 2311-201202
groov
EPIC Learning Center Setup
groov
EPIC Learning Center Setup
Form 2311-201202
PAGE 2
ASSEMBLING THE LEARNING CENTER
1.
Let’s start by adjusting the handle/kickstand in the back.
a.
After you remove the Learning Center from the box, place it on a stable surface,
upside down, with the top edge of the unit and the acrylic stand sitting on the
surface.
Do not
place the Learning Center with the touchscreen laying flat on
the surface. You may damage the touchscreen.
b.
With the back of the unit facing you, locate the pin on one side of the handle,
near the acrylic surface. Hook your finger into the ring and pull out the pin.
c.
Adjust the handle to align the holes to the desired position, then insert the pin.
–
Position 1: Orients the Learning Center so that it’s easier to see while sitting
at your desk.
–
Position 2: Orients the Learning Center so that it’s easier for an audience to see it.
2.
Grab the Learning Center with both hands and turn it right-side up, so that the bottom edge of the acrylic stand and the kickstand sit on the
surface.
3.
Connect an Ethernet cable and the temperature probe.
a.
Lift the touchscreen. Connect an
Ethernet cable (that’s connected
to your network) to the ETH0
network interface, which is the
top interface of the two
interfaces located on the
underside of the
groov
EPIC
processor.
b.
Connect the temperature probe
to the temperature probe
connector on the acrylic stand.
4.
Turn the Learning Center around so you can see the back.
a.
Connect the DC connector end of the power cord to the DC socket.
b.
Connect the power cord to the adapter.
c.
Connect the power adapter to the outlet of 110 to 240 VAC power.
5.
You can illuminate the Learning Center with three different
light settings:
–
To provide a steady blue illumination, set the switch to the
top position.
–
To turn off the light, set the switch to the middle position.
–
To be able to program the illumination, set the switch to
the bottom position.
6.
Turn the Learning Center around so you can see the front. Turn
on the processor and close the touchscreen.
INITIALIZING THE LEARNING CENTER
1.
When the touchscreen displays the Welcome! screen, make a note of the value in the Hostname or Eth0 IP Address box.
2.
Open a web browser on your computer and type in the following as the URL, entering the Hostname (or Eth0 IP address) from the previous step
in place of <hostname>:
https://<hostname>
For example:
https://opto-03-fa-bf
or
https://xxx.xxx.x.xxx
, where
xxx.xxx.x.xxx
is the IP address shown in the
Eth0 IP Address field.
3.
If your browser displays a warning about security, you can accept the warning and proceed to connecting to the processor.
4.
Click Let’s get started!
5.
In the Create an Account screen, type in the username and password that follows strong security recommendations. This username and
password is the first administrator level user for your Learning Center.
Remember it!
groov
EPIC does not provide a way to recover a lost
password or username. Click Create Account.
6.
We recommend that you check that the version of
groov
EPIC processor firmware running on the Learning Center is the latest version. Click
Configure Device > Info and Help > About.
7.
Write down the Restore Version: ____________________________________
8.
Open the black envelope and pull out the GRV-EPIC-PR1 Activation Certificate. Follow the instructions on the certificate to activate your
groov
EPIC processor. When you reach the profile page for your
groov
EPIC processor, under the Latest Releases section, note the version number for the
groov
EPIC Field Update. Compare this version number with the Restore Version number you noted in
above:
–
If the version number for the
groov
EPIC Field Update is the same as or lower than the Restore Version number, then you have the latest
firmware installed on your processor! You can skip the rest of this step.
–
If the version number for the
groov
EPIC Field Update is higher than the Restore Version number, you’ll need to download and install the
newer version of the firmware that’s on the webiste. Follow the instructions in “Updating Firmware on a
groov
EPIC Unit” in the
EPIC
User’s Guide (form 2267)
. You can skip step 5 (creating a backup of your unit) and step 6 (deactivating the Ignition Edge license).
Your
groov
EPIC Learning Center is now up and running!
To learn how to program and manage your
groov
EPIC Learning Center, see our online training by visiting
, selecting
groov
EPIC
Training Series, and enjoy exploring your Learning Center! If you are interested classroom training, you can learn more by visiting our website
(
) and looking up
.
Example
Values for your Learning Center
Hostname:
______________________________________
Eth0 IP Address:
_______________________________________
Step 6.
Step 5.
Steady blue
Off
Programmable
Step a.
Step b.
Step c.
Step b.
Step c.
Position 1
Position 2
Step a
Step b
Step a (enlarged)
