Optimum OPTIMILL MH 28V Operating Instructions Manual Download Page 60

Page: 60 / 60

OPTIMUM

M A S C H I N E N - G E R M A N Y



Version 1.0.1 dated 30 / 08 / 2012

Page 60

Original operating instructions

MH28V

Index

Appendix

....................................................... 54

Changing the speed range

............................ 28

Cleaning and lubricating

................................ 22

Control and indicating elements

.................... 24

Control panel

................................................. 25

Dimensions

................................................... 16

Disassembly of tool

....................................... 27

Disconnecting the drilling-milling machine

.... 14

Drilling-milling capacity

.................................. 16

EC - Declaration of Conformity

..................... 59

Environmental conditions

.............................. 17

Extent of supply

............................................. 19

First use

........................................................ 22

Inserting a tool

............................................... 27

Inspection

...................................................... 34

Installation and assembly

.............................. 21

Load suspension point

.................................. 21

Maintenance

.................................................. 34

Malfunctions

.................................................. 53

Manual spindle sleeve feed

........................... 31

Operation

...................................................... 24

Optional accessory

........................................ 23

Power supply

........................................... 16

Product follow-up

.......................................... 58

Proper use

....................................................... 7

Protective cover

............................................ 12

Qualification of personnel

Safety

.................... 10

Reasonably foreseeable misuse

..................... 8

Repair

............................................................ 34

Safety check

.................................................. 13

Safety devices

............................................... 11

Safety during operation

................................. 14

Safety warnings

............................................... 6

Securing the drilling-milling machine

............. 14

Selecting the speed

....................................... 29

Setting instructions control

............................ 40

Speeds

.......................................................... 17

Spindle holding fixture

................................... 16

Standards values for cutting speeds

..............29

Switching on the machine

..............................26

Switching-on

..................................................26

Swivelling the drill-mill head

...........................33

Technical data

................................................16

Dimensions

.....................16

Drilling-milling capacity

.....................16

Environmental conditions

.....................17

Power supply

.....................16

Speeds

.....................17

Spindle holding fixture

.....................16

Work area

.....................17

Transport

........................................................19

Use of collet chucks

.......................................27

Using lifting equipment

...................................14

Warming up the machine

...............................23

Work area

......................................................17

Summary of Contents for OPTIMILL MH 28V





























































Search results

Summary of Contents for OPTIMILL MH 28V

Reviews:

Related manuals for OPTIMILL MH 28V

Brands by name

Popular brands

Optimum OPTIMILL MH 28V, Operating Instructions Manual

Search results

Summary of Contents for OPTIMILL MH 28V

Reviews:

Related manuals for OPTIMILL MH 28V

Brands by name

Popular brands