Optimum OPTIMILL MH 28V Operating Instructions Manual Download Page 5

Page: 5 / 60

OPTIMUM

M A S C H I N E N - G E R M A N Y



201

Safety

Version 1.0.1 dated 30 / 08 / 2012

Page 5

Original operating instructions

MH28V

Safety

Glossary of symbols

This part of the operating manual



explains the meaning and use of the warning references contained in the operating man-
ual,



explains how to use the drilling-milling machine properly,



highlights the dangers that might arise for you and others if these instructions are not
obeyed,



informs you on how to prevent dangers.

In addition to this operating manual please observe



applicable laws and regulations,



legal regulations for accident prevention,



the prohibition, warning and mandatory signs as well as the warning notes on the drill-
ing-milling machine.

Always keep this documentation close to the drilling-milling machine.

INFORMATION

If you are unable to solve a problem using this manual, please contact us for advice:

Optimum Maschinen Germany GmbH
Dr. Robert-Pfleger-Str. 26

D- 96103 Hallstadt

Telefon: +49 (0) 900 - 19 68 220 (0,49 €/min.)

E-Mail: [email protected]



gives additional indications



calls on you to act



enumerations

Summary of Contents for OPTIMILL MH 28V





























































Search results

Summary of Contents for OPTIMILL MH 28V

Reviews:

Related manuals for OPTIMILL MH 28V

Brands by name

Popular brands

Optimum OPTIMILL MH 28V, Operating Instructions Manual

Search results

Summary of Contents for OPTIMILL MH 28V

Reviews:

Related manuals for OPTIMILL MH 28V

Brands by name

Popular brands