manualshive.com logo in svg

Optimum B 34 H Vario, Operating Manual

Share
Download
Optimum B 34 H Vario Operating Manual Download Page 8

Safety

OPTIMUM

M A S C H I N E N   -   G E R M A N Y

21 / 07 / 2014

Page 8

Safety  Upright drill B34 H/ B34 H Vario ; Version 1.0.5



 201

4

US

1.2

Proper use

WARNING!

In the event of improper use of the upright drill
•

there may be a risk to personnel,

•

there may be a risk to the machine and other items,

correct functioning of the upright drill may be affected.

The upright drill is designed and manufactured to be used in environments where there is no
potential danger of explosion. The upright drill is designed and manufactured to produce holes
in cold metal or other not health hazardous or non- flammable material by using a rotating cut-
ting tool with several chucking grooves.

If the upright drill is used in any way other than described above, or modified without authoriza-
tion,  then the upright drill- is being used improperly. 

We do not take liability for damage caused through improper use.

We would like to stress that any modifications to the construction, or technical or technological
modifications that have not been authorized will also render the warranty null and void.

It is also part of proper use that

the maximum values of the upright drill are complied with,

the operating manual is constantly observed, 

inspection and maintenance instructions are observed.



 „Technical Data“ on page 16

WARNING!

Very serious injury. 

It is forbidden to make any modifications or alternations to the operating values of the  
upright drill! They could endanger employees and cause damage to theupright drill. 

1.3

Possible dangers caused by the upright drill.

The upright drill is state of the art.

Nevertheless, there is a residual risk as the upright drill operates with

high revolutions,

rotating parts,

electrical voltage and currents.

We have used construction resources and safety techniques to minimize the health risk to per-
sons resulting from these hazards.

If the upright drill is used and maintained by employees who are poorly qualified, then there
might be a risk resulting from incorrect operation and unsuitable maintenance of the upright drill.

INFORMATION

Everyone involved in the assembly, commissioning, operation and maintenance must

be duly qualified,

strictly follow this operating manual.

Due to improper use

there is a risk for the employee,

the machine and further property might be endangered,

the function of the upright drill could be effected.

Summary of Contents for B 34 H Vario















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands