manualshive.com logo in svg

Optical dimensions LASER CHECK 6212A, Manual, Page: 9 / 66

Share
Download
Optical dimensions LASER CHECK 6212A Manual Download Page 9

 

 

 

 

6212A Manual Version 14.56.docx

 

Page 1 of 58 

 

PERFORMANCE SPECIFICATIONS 

Measurement / Detection Method

 

Angle resolved laser scattering

 

Measurement speed

 

Single measurement in < 0.5 seconds

 

Measurement range

 

0.5 µinch to 40 µinch / 0.0125 µm to 1.0 µm

 

Repeatability

 

± 3.0% of measured value

 

Spot size (area-measured)

 

5 mm X 1 mm

 

Environmental considerations (temperature / humidity):

  

Operating

 

-10º C to +55º C / 10% to 90% RH

 

Storage

 

-40º C to +80º C / 1% to 99% RH

 

Power requirements

 

110 / 220 VAC, 50 / 60 Hz

 

Other Features 

Factory Calibrated to Ra Ground Surface Standards  

Works on any material/color (rubber, glass, steel, etc.) 

RS232 Interface Option 

Stored items: 

All Roughness Values 

Date and Time 

Average Ra Roughness and Standard Deviation 

Minimum / Maximum Ra Roughness 

CSV text Formatted File 

 

Summary of Contents for LASER CHECK 6212A



































































Reviews:

No comments