ON
1
2
3
4
5
6
ON
1
2
3
4
5
6
RX CORE SERIES
BATTERY OPERATED PIR / MICROWAVE COMBINATION DETECTOR
BATTERY OPERATED PIR / MICROWAVE COMBINATION DETECTOR
RX CORE SERIES
<1m
RXC-RDT
RXC-RDT
RXC-RDT shall be mounted in a position where
expected intrusion is in perpendicular the
detection patterns.
INSTALLATION INSTRUCTIONS
DE
IT
PT
ES
CONSIGNES D'UTILISATION
ISTRUZIONI INSTALLAZIONE
INSTALLATIONSANLEITUNG
INSTRUÇÕES DE INSTALAÇÃO
INSTRUCCIONES DE INSTALACIÓN
FR
EN
The nix sign indicates prohibition.
Warning
Caution
1
PARTS IDENTIFICATION
3
INSTALLATION
Installation
Installation
Installazione
Instalação
Instalación
3-2 WIRING DIAGRAM
3-1 WIRELESS TRANSMITTER PREPARATION
Unit: mm (inch)
Connectors to be used
Connector for POWER and ALARM
Connector for TROUBLE
Red
Black
How to position a battery
4
DETECTION ZONE
Zone de détection
Erfassungsbereich
Zone di rilevazione
Zona de detecção
Zona de detección
Note>>
30 (1.18)
92 (3.62)
44 (1.73)
5
SWITCH SETTING
DIP switch
1 WALK TEST MODE
2 LED
3,4 PIR SENSITIVITY
5 ALARM & TROUBLE OUTPUT
6 MICROWAVE RANGE
2
INSTALLATION HINTS
Conseils d'installation
Installations-Tipps
Indicazioni installazione
Dicas de instalação
Recomendaciones de instalación
TOP VIEW
5
10
15
25
30
35
40 ft
6 m
4
2
15
10
5
20 ft
2
4
6
8
10
12 m
4
6 m
0
2
0
5
10
15
20 ft
20
MW Short
MW Long
PIR
SIDE VIEW
5
10
15
20
25
30
35
40 ft
0
2.4 m
12 m
10
8
6
4
2
0
8 ft
MW Short
MW Long
PIR
No. 59-2043-4 1703-16
DIP switch 1
-WALK TEST MODE
POSITION
FUNCTION
TEST
(Factory default)
NORM
DIP switch 6
-MICROWAVE RANGE
DIP switch 2
-LED
DIP switch 5
-ALARM & TROUBLE OUTPUT
DIP switch 3,4
-PIR SENSITIVITY
NORM
⇔
TEST
ON
1
2
3
4
5
6
OFF
⇔
ON
ON
1
2
3
4
5
6
ON
1
2
3
4
5
6
N.C.
⇔
N.O.
ON
1
2
3
4
5
6
SHORT
⇔
LONG
ON
1
2
3
4
5
6
The LED lights irrespective of
the DIP switch 2 (LED)
setting.
The LED lights depending on
the DIP switch 2 (LED)
setting.
POSITION
FUNCTION
ON
LED ON
LED OFF
Note>>
If the LED lights, check the
DIP switch 1 (WALK TEST
MODE) setting.
OFF
(Factory default)
POSITION
FUNCTION
N.O.
N.O. output
N.C. output
N.C.
(Factory default)
POSITION
FUNCTION
SHORT
LONG
(Factory default)
Lens
Wall tamper
<1m
<1m
RXC-RDT-X5: 10.525 GHz
RXC-RDT-X8: 10.587 GHz
DE
IT
PT
ES
FR
DE
IT
PT
ES
FR
DE
IT
PT
ES
FR
Cover
Back Box
Chassis
Identification des pieces
Teilekennzeichnung
Descrizione delle parti
Identificação das partes
Identificación de las partes
DE
IT
PT
ES
FR
Transmitter side
Main unit side
Red
Black
White
Yellow
Red: Power input (+)
Black: Power input (-)
White: Alarm
Yellow: Alarm
Green: Trouble
Blue: Trouble
Brown: Wall tamper
Orange: Wall tamper
Gray: Wall tamper
Green
Blue
Brown
Orange
Gray
Trouble
Wall tamper
Alarm
Wireless
transmitter
Back box
Main unit
Reglagles des interrupteur DIP
Schaltereinstellungen
Impostazione dei selettori
Ajuste da chave DIP
Ajuste del conmutador DIP
DE
IT
PT
ES
FR
Velcro tape
Screw kit
For wall mounting
Screw (3 × 16 mm) ×3
Connector for POWER and ALARM
Connector for TROUBLE
ON
1
2
3
4
5
6
POSITION
FUNCTION
(Factory default)
3
4
High sensitivity
Low sensitivity
3
4
3
4
3
4
Middle sensitivity
Super High sensitivity
7 m (24 ft)
Note>>
Once any output is activated, the
battery saving circuit requires 2
minutes of inactivity before the next
output.
3-3 MOUNTING
1
Remove the cover.
Twist
Loosen
3
Separate the chassis from the back box.
2
Remove the board.
Push
Pull
Do not
touch
12 m (40 ft)
5
Mount the Wireless transmitter to the backbox
or backside of the chassis.
Velcro tape
transmitter
Back box >>
Backside of the chassis >>
Velcro tape
transmitter
4
Mount the back box to the wall.
Note>>
Mounting screws are not included.
Corner mounting >>
Backside mounting >>
