manualshive.com logo in svg

Optex ELITE PRO, Instruction Manual, Page: 5 / 24

Share
Download
Optex ELITE PRO Instruction Manual Download Page 5

Preface

Installation

Troubleshooting

Specifications

5

Installation

Install in the order of OC-907C T, OA-607 T, door loop.

Below is a configuration example with the ELITE PRO.

Loop harness

2200 mm

OC-907C T

OA-607 T

Step 2) Installing OA-607 T

▪ 

Drill the following holes

OA-607 T mounting holes

Door loop cover mounting holes

Through hole

Step 3) Installing the door loop

▪ 

Drill the following holes

Jamb cover mounting hole

Wiring hole (concealed)

Side view

Step 6) Fitting the cover on OA-607 T

To power

To the door controller

Step 1) Installing OC-907C T and 

connecting the loop harness

▪

 Connect the loop harness connector 

to the OC-907C T.

Step 4) Connecting the door front/back 

OA-607 T

Step 5) Setting the OA-607 T threshold 

area angle screw and swing area 

angle screw

Step 7) OC-907C T and door controller I/O 

wiring and OC-907C T power wiring

Prepare the tools required in advance.
Example:

(1)

(2)

(3)

(4)

(5)

(6)

(7) (8)

(1) #1 Phillips head screwdriver 

(2) #2 Phillips head screwdriver 

(3) Flat head screwdriver 

(4) Crimping tool 

(5) Pliers 

(6) Drill 

(7) 1/8” drill bit 

(8) 3/8” drill bit

WARNING

WARNING

Danger of electric shock

Before starting the procedure, make sure that the power is turned OFF.
When passing the cable through the hole, do not tear the shield otherwise it may cause electric shock or breakdown of the sensor.

Summary of Contents for ELITE PRO

























Reviews:

No comments