manualshive.com logo in svg

Onlogic K800, Product Manual

Share
Download
Onlogic K800 Product Manual Download Page 28

The Pykarbon module is designed to be a simple and easy tool for configuring your system to meet
your needs and applications. Visit

OnLogic’s Pykarbon GitHub page

for specific information regarding

using the interface tool.

6 - Power Management

6.1 - Wake-Up Events

Karbon 800 supports multiple power states. The wake-up events can be configured in the MCU and
BIOS. This section describes the power management functions you can perform and gives
information on protection circuitry for power adapters.

Wake-Up Event

From ACPI State

Comments

Power Button

Deep S5 , S5, S3

Ignition

Ultra-low power,

Deep S5, S5, S3

Must be enabled in MCU

Digital Input

S5, S3

Must be enabled in MCU

LAN

S3

Must be enabled in BIOS

USB

S3

RTC Alarm

S5, S3

Must be enabled in BIOS

6.2 - Protection Circuitry

Parameter

Value

Nominal operating voltage (Rated DC value of input)

12~48V

Undervoltage protection trip DC level (system turns off)

7.6V

Overvoltage protection trip DC level (system turns off)

52.5V

Maximum safe DC voltage (system not damaged)

56V

Minimum safe reverse voltage (system not damaged)

-36V

Ignition pin safe working voltage (system not damaged)

56V

These DC levels specified are the absolute max values for the pins for function and safety of the
system. The protection circuitry allows for brief transient voltages above these levels without the
system turning off.

27

Summary of Contents for K800







































Reviews:

No comments

Brands by name

Popular brands

Load more brands