Onkyo TX-RZ3400 Instruction Manual Download

Page: 119 / 205

119

≫

≫

≫

≫

≫

≫

Playing Back (ZONE 3)

In remote controller operation, while pressing and holding the ZONE 3 button,

press other buttons for operation.

1. While pressing and holding the ZONE 3 button on the remote controller, point

the remote controller at this unit and press .

• "Z3" on the display of the main unit lights up.

2. While pressing and holding the ZONE 3 button on the remote controller, press

the input selector of the input source you want to play in the separate room. To

control on the main unit, press the ZONE 3 button, and then within 8 seconds,

press the input selector button of the input to be played in the separate room.

To play the same source in the main room and separate room, press the

ZONE 3 button of the main unit twice.

3. If the unit is connected to the pre-main amplifier in the separate room, adjust

the volume on the pre-main amplifier. If the unit is connected to the power

amplifier or ZONE speaker in the separate room, adjust the volume with the

volume button while pressing and holding the ZONE 3 button on the remote

controller. To do this on the main unit, press the ZONE 3 button, and then

within 8 seconds, adjust the volume using the MASTER VOLUME dial.

• When connecting the power amplifier, set "6. Multi Zone" - "Zone 3" -

"Output Level" (

p176

) to "Variable" on the Setup menu. If it is not set,

a large volume is output and the power amplifier, speakers, etc. may be

damaged.

• If you turn the unit to standby during multi-zone playback, the Z3 indicator is

dimmed, and the playback mode is switched to playback in a separate room

only. Setting ZONE 3 to on while the unit is in standby also switches the

playback mode to playback in the separate room only.

• For ZONE 3 output, audio from externally connected AV components can be

output only when it is an analog audio signal.

• DSD audio signals cannot be output to ZONE 3 with the "NET" input selector.

• If ZONE 3 is on, power consumption during standby will increase.

• If ZONE 3 is turned on when the Pure Audio listening mode is selected in the

Summary of Contents for TX-RZ3400













































































































































































































Search results

Summary of Contents for TX-RZ3400

Reviews:

Related manuals for TX-RZ3400

Brands by name

Popular brands

Onkyo TX-RZ3400, Instruction Manual

Search results

Summary of Contents for TX-RZ3400

Reviews:

Related manuals for TX-RZ3400

Brands by name

Popular brands