background image

118

Setup

Setup

2. Speaker

 

„

3. Distance

Set the distance from each speaker to the listening position.

 

‰

Front Left  

(Default Value: 12.0 ft/3.60 m) 

Center  

(Default Value: 12.0 ft/3.60 m) 

Front Right  

(Default Value: 12.0 ft/3.60 m) 

Height 1 Left   (Default Value: 9.0 ft/2.70 m) 

Height 1 Right   (Default Value: 9.0 ft/2.70 m) 

Height 2 Left   (Default Value: 9.0 ft/2.70 m) 

Height 2 Right   (Default Value: 9.0 ft/2.70 m) 

Surround Right  (Default Value: 7.0 ft/2.10 m) 

Surr Back Right  (Default Value: 7.0 ft/2.10 m) 

Surr Back Left   (Default Value: 7.0 ft/2.10 m) 

Surround Left   (Default Value: 7.0 ft/2.10 m) 

Subwoofer  

(Default Value: 12.0 ft/3.60 m)

• 

Default values vary depending on the regions.

• 

The unit of distance can be changed by pressing the MODE button on the 

remote controller. When using the unit "feet", the setting is available in 

increments of 0.1 ft from 0.1 ft to 30.0 ft. When using the unit "meter", the 

setting is available in increments of 0.03 m from 0.03 m to 9.00 m.

• 

When measurements are made using Dirac Live ( 

p144,

 

p148

), units are 

displayed as "msec" and the value cannot be changed.

(Height 1 Left, Height 1 Right, Height 2 Left, Height 2 Right, Surr Back Right, 

Surr Back Left): 

• 

Depending on the use of the ZONE speakers, it may not be possible to select 

this setting.

 

„

4. Level Calibration

Adjust the volume level of each speaker.

 

‰

Front Left  

(Default Value: 0.0 dB) 

Center  

(Default Value: 0.0 dB) 

Front Right  

(Default Value: 0.0 dB) 

Height 1 Left   (Default Value: 0.0 dB) 

Height 1 Right   (Default Value: 0.0 dB) 

Height 2 Left   (Default Value: 0.0 dB) 

Height 2 Right   (Default Value: 0.0 dB) 

Surround Right  (Default Value: 0.0 dB) 

Surr Back Right  (Default Value: 0.0 dB) 

Surr Back Left   (Default Value: 0.0 dB) 

Surround Left   (Default Value: 0.0 dB) 

Subwoofer  

(Default Value: 0.0 dB)

Select a value between "-12.0 dB" and "+12.0 dB" ("-15.0 dB" and "+12.0 dB" 

for Subwoofer) (in 0.5 dB increments). A test tone will be output each time you 

change the value. Select the desired level.

(Height 1 Left, Height 1 Right, Height 2 Left, Height 2 Right, Surr Back Right, 

Surr Back Left): 

• 

Depending on the use of the ZONE speakers, it may not be possible to select 

this setting.

Summary of Contents for TX-NR7100
































































































































































































Reviews: