background image

 
 
 
 

9051_Bedienungsanleitung_C1_Rev2_EN_UK – Stand 08.08.2018 TS / MB 

 

Warranty 

We provide a 24-month warranty on this desk base. The warranty covers all material and production errors and 
applies from the date of production (see rating plate). The warranty is only valid under the condition that the 
desk base has been properly and professionally assembled and has been used within the scope of the 
described parameters; that maintenance has been performed correctly and that repairs have been performed 
solely by authorised service staff. 
 
The sit/stand desk must not be improperly handled or used and no changes  are permitted to be made on the 
desk base; otherwise the warranty expires. Please refer to our General Terms and Conditions for additional 
information. 
 

Maintenance / Cleaning 

Regularly remove dust and dirt from the desk base, in particular from the guide tubes, and make sure that there 
are no damages and cracks. 
 
Check all fastening screws to make sure they are securely fastened and check all plug connectors, cables and 
plugs including proper functioning. 
 
 

Danger:

  Clean the controller, actuator and the desk base only with a dry or slightly moist cloth.  

Danger to life!

 

 
 
 

Attention: 

Aggressive cleaning agents can cause damage or discolourations on the product. Use 

only agents with pH-values of 6-8. 

 
 
 

Danger:

 Never let any fluids get into the system (controller, actuator, cable and base). 

Danger to 

life!

 

 
 

 

Summary of Contents for FREE.STAND 9051




























Reviews: