manualshive.com logo in svg

Omron ZX-CAL, Operation Manuals, Page: 25 / 187

Share
Download
Omron ZX-CAL Operation Manuals Download Page 25

External Amplifier Unit I/O

Section 1-2

5

1-2

External Amplifier Unit I/O

The following functions are allocated to the external I/O lines.

 Refer 

to 

3-2 Hardware Functions

 for I/O functions.

Note 1.

Use a separate stabilized power supply for the Amplifier Unit, particu-
larly when high resolution is required.

2.

Wire the Unit correctly. Incorrect wiring may result in damage to the
Unit. (Do not allow the I/O lines, particularly the linear output, to come
into contact with other lines.)

3.

Use the 0-V ground line (blue line) for the power supply and use the
shield wire (linear output ground) together with the linear output (black
line) for linear output. Each of these grounds must be used for the
designed purpose. When not using the linear output, connect the lin-
ear output ground to the 0-V ground line.

 

12 to 24 VDC

GND (0 V)

HIGH output

PASS output

LOW output

Linear output

Linear output GND

Laser OFF input

Zero reset input

Timing input

Reset input

Brown

Blue

White

Black

Green

Shield

Gray

Pink
Orange

Purple

Red

Z157-E1-01C.book  Page 5  Thursday, August 31, 2006  5:13 PM

Summary of Contents for ZX-CAL




























































































































































































Reviews:

No comments