Omron ZW-7000 Series User Manual Download Page 148

Page: 148 / 336

Setting the Output Conditions

146

ZW-8000/7000/5000

User's Manual

Performing 2-point Scaling

Measurement is performed at two positions, and offset values are set for those measured values.

Example: When correcting display values to match actual distances

Separate the two specified points by at least 1% of the rated measuring range for the connected Sensor Head.

For example, for the ZW-S7010, the two measured points must be separated by at least 1 mm

0.01 = 0.01 mm as

the measuring range is 1 mm (± 0.5 mm).



Multi View Explore

: [Bank Group] | [(Bank Data Name)] (double click)

→

Edit pane

: [Task Settings] icon (

)

→

Task Settings window : [Scaling]

Item

Setting item

Setting value

Description

Actual scaling
(two points)

Set value

(1st point)

-999.999999 to 999.999999 [mm]

Correct the measured value of the 1st point, and set the
value to display.

Set value

(2nd point)

-999.999999 to 999.999999 [mm]

Correct the measured value of the 2nd point, and set the
value to display.

Set the [Scaling] to OFF.

Click [Auto setting].

The [Scaling] popup menu appears.

1.0

-1.0

-0.9

0.9

-1.0

1.0

y v

(mm)

asu

red v

(mm)

Point 2

Point 1

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands

Omron ZW-7000 Series, User Manual

Search results

Summary of Contents for ZW-7000 Series

Reviews:

Brands by name

Popular brands