manualshive.com logo in svg

Omron ZW-7000 Series, User Manual

Share
Download
Omron ZW-7000 Series User Manual Download Page 116

Performing internal logging

114

ZW-8000/7000/5000 

User's Manual

3-8 Performing internal logging

Up to 2000000 data of measurement values can be logged in the Sensor Controller's internal memory.

Internal logging can be started or ended using Sysmac Studio, parallel I/O, or non-procedural communications 

commands.

The operating procedures for each method are shown below.

The settings that can be enabled for each method are shown below.

Internal logging cannot be executed when in the following settings. 

• When overwrite mode is ON or when the measurement cycle (internal synchronous measurement mode) is less 

than 40µs

Internal logging by Sysmac Studio

Data logging conditions and logging start/end timing can be set with Sysmac Studio.

 Multi view Explore

: [(ZW model name)] (double click)

 

→

 Edit pane

: [Online] icon (

)

 

→

 Online setting window : [Internal Logging]

Function

Sysmac Studio

Parallel I/O

Non-procedural commu-
nications commands

Specify start timing

Press the "Logging Start" button.

LOGGING input ON

Send LS command

Specify end timing

Stops automatically after the specified 
number of logging data has been saved.

LOGGING input OFF

Send LE command

Terminate logging

After pressing the "Logging Start" button, 
press the displayed "Terminate" button

LOGGING input OFF

LE command

Output logging data

Press the "Save to file (Sensor 

→

 PC)" 

button.

Send LO/LG 
command

Send LO/LG command

Clear logging data

• Automatically cleared after the "Logging 

Start" button is pressed if clear logging 
data is turned ON when logging starts

• Cleared when "Clear Logging Data" button 

is pressed

Send LC command

Send LC command

Get logging information

Press the "Get logging information" button.

-

Send LI command

Function

Sysmac Studio

Parallel I/O

Non-procedural 
communications 
commands

Overwrite mode

Sets the operation to be performed when the logging 
count exceeds the set number of logging data. 

OFF: Internal logging is stopped. 
ON : The oldest logging data is overwritten.

OFF

ON/OFF

ON/OFF

Label insert mode

Sets the operation to be performed when logging input 
is turned on. 

OFF: No operation. 
ON : When logging input is turned on, inserts label 

into logging data.

OFF

ON/OFF

ON/OFF

Output data format

−

ASCII

ASCII/Binary

ASCII/Binary

Important

Summary of Contents for ZW-7000 Series

















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands